Hospitality Polidress 10% – 1LT Retail, 1LT x 12, 5LT, 5LT x 4, 25LT, 200LT and 1000LT

Description

Product Overview: What is Polidress 10%

• Polidress 10% is described as a medium-duty acrylic/polymer floor dressing — i.e. a thin polymer coating for sealed floors, intended for maintenance / regular use on floors that have already been sealed.

• It contains about 10% solids, meaning it’s a lighter / lower-solid-content dressing compared to heavier sealers.

• The product is water-based (as are the other floor-care coatings in the same product line) which implies easier application and easier stripping (when needed) compared to solvent-based finishes.

• Purpose: Polidress 10% is used as a maintenance / re-coating layer on already sealed floors — to restore shine, maintain floor protection, and prolong the life of the floor covering under light-to-medium traffic and regular maintenance cycles.

📦 Available Sizes / Packaging

Polidress 10% is available in:

• 1 L — retail bottle

• 12 × 1 L (case pack) — for resale or bulk small-volume users

• 5 L container

• 4 × 5 L (i.e. case of four 5 L) — for larger or frequent users

• 25 L container (bulk) — for institutional / commercial / large-scale use

• 200 L (drum) — for high-volume / industrial-scale floor maintenance (though product page does not explicitly list 200 L, many of their floor-care items use this pack size; you might want to confirm with supplier)

• 1000 L IBC / flow-bin (bulk) — same note as above, for very large-scale maintenance or contracts

🔧 Typical Use & Application (What It’s For)

• It is a medium-duty floor coating used as a weekly (or regular) maintenance coating on sealed floors. That means after initial sealing and stripping cycles, Polidress 10% helps maintain floor finish and protection under regular foot traffic.

• Because it’s a lighter (10% solids) dressing, it is not the “heavy-duty sealer” but rather a maintenance coat — suitable for surfaces that have already been sealed and for regular maintenance cycles.

• It likely helps maintain gloss/shine, floor protection and smoothness, and reduces wear — ideal for hospitality, commercial, institutional floors (offices, hotels, hospitals, etc.) where frequent re-coating with heavy-duty sealer may not be necessary, but periodic maintenance is required.

• As with other water-based polymer floor finishes in the same line (e.g. heavier “Polidress 16%,” “Polidress 21%,” or “Polidress 25%”), after cleaning and stripping (when needed), Polidress 10% can be applied to provide protective finish.

🧪 How It Compares Within the Floor-Care Range

Within floor-care range, Polidress 10% sits on the “lighter maintenance coating / dressing” end of the spectrum.

• For heavier protection or higher shine / durability needs, there are stronger sealers/dressings (e.g. “Polidress 16%,” “Polidress 21%,” “Polidress 25%”) — these likely have higher solids and deliver thicker protective / glossy coats.

• Polidress 10% — with 10% solids — is optimized for regular upkeep, light-to-medium traffic areas, or frequent maintenance regimes (e.g. hotels, offices, low-traffic corridors) where heavy-duty coating may be overkill.

• Because it’s water-based and part of the same “hospitality floor care” line, it is compatible with the brand’s recommended stripper product (e.g. their “strip & reseal” cycle) if you need to fully recoat.

📝 What’s Missing / What to Confirm (Before Use)

• The public product page for Polidress 10% does not (at least in the sources I saw) list detailed pH, chemical composition, or coverage rate (e.g. how many m² per liter). The manufacturer tends to provide these details only in their technical data sheet (TDS), which might be available on request.

• If using for institutional cleaning contracts or for compliance, you may want to request the full TDS / SDS (Safety Data Sheet) from EM Supply Direct to confirm application instructions, drying times, compatibility, and safety/handling procedures.